Ademco 4140XMPT2 Basic Commands

Zones 9 Hardwired, up to 64 total zones with wireless

Partitions 8

Wireless Yes

Batteries Main Panel 12 volt rechargeable Gel-Cell inside main panel

AC Transformer is 16.5 Volts

Doors/ Windows/Motions 3-volt Lithium (Panasonic CR123A)

Smoke Detector 2 9-volt Alkalines

Keyfobs and Panics 2 3-volt Lithium (CR2025 or CR2430 Lithium)

Panic Buttons Police Panic - * and #

Fire Panic - 1 and *

Medical Panic - 3 and #

Status Press * if keypad shows NOT READY to view open zones

Arm Away 4-digit code + 2 (AWAY) to arm everything

Arm Stay 4-digit code + 3 (STAY) to arm everything but motions

Quick-Arm (If Enabled) # + 2 for AWAY, # + 3 for STAY

Instant Arm 4-digit code + 7 (INSTANT), also bypasses motions

Max Arming 4-digit code + 4 (MAX), arms everything including motions instant

Disarm 4-digit code + 1 (OFF)

Silence Alarm 4-digit code + 1 (OFF) twice to turn off siren and reset display

Bypass 4-digit code + 6 (BYPASS) + Zone (01, 02 03 etc)

(Keypad will beep and BYPASS + Zone will show on display)

Door Chimes 4-digit code + 9 (CHIME)

Reset Smoke 4-digit code + 1 (OFF) twice to turn off siren and reset smoke

(If this does NOT reset smoke detector set for service, smoke is bad)

View Event Log 1. Enter Master Code + # + 60 (Alpha keypads only)

2. Display will ask for most recent or complete, * to exit

Tech_201000000200.gif 0 = Most recent

  1. = All Events

3. View events in all partitions or choose partition, * to exit

Tech_201000000229.gif 0 = All Partitions

  1. or 2 = Partition 1 to 2

4. Choose which event log to view with 1 or 3, press 8 to enter, * to exit

Tech_201000000202.gif Alarms

Tech_201000000203.gif Zone Troubles or Supervisory

Tech_201000000204.gif Zone Bypass

Tech_201000000205.gif Arming (Open)/Disarming (Close)

Tech_201000000206.gif Panel Troubles (AC Fail, Com Fail etc)

Tech_201000000207.gif All Events

5. Last event is displayed, press 1 for previous or 3 for next, * to exit

Tech_201000000208.gif Alarm occured on Zone 03

Tech_201000000209.gif User 4 disarmed Partition 1

Tech_201000000210.gif Tamper on Zone 32

Tech_201000000211.gif No more events, press * to exit

Clear Event Log 1. Enter Master Code + # + 62 (Alpha keypads only)

  1. Display will to clear event log, * to exit

    Tech_201000000212.gif
0 = No

  1. = Yes

3. Display will confirm deleting event log, * to exit

Tech_201000000213.gif 0 = No

  1. = Yes

4. Display will clear and return to main screen

Tech_201000000214.gif

Voice Keypads

Voice Chime # + 0 + 2 + 4 to Enable or Disable (Keypad should say "ON" or "OFF")

Show Status # + 0 + *

Show Faults Press * *

Record 1. Press # + 0 + 1 (LED turns ON)

Message 2. Record message up to 2.5 minutes

3. Press 1 to end (LED begins FLASHING)

Play 1. Press # + 0 + 3

Message 2. Recorded message will play (LED turns OFF)

Adjust Volume Press # + 0 + 2 then press 3 or 6 to raise or lower volume

Test Sensors 4-digit Code + 5 (TEST)

Keypad will beep every 3 minutes

Open sensors and keypad will sound

End test with 4-digit Code + 1 (OFF) key

(Wireless motions require no movement for 4 minutes prior to testing)

Setting Clock (some systems may not allow changing Clock)

1. Enter Master Code + # + 63, display will show current Time/Date

2. Enter correct (00 to 12) Hour then press *

3. Enter correct Minutes (00 to 59) then press *

4. Press any key from 0 to 9 to toggle AM and PM then press *

5. Enter correct Month (01 to 12) then press *

6. Enter correct Date (01 to 31) then press *

7. Enter correct Year (99 or 00 etc) then press *

2. Press * after cursor is in the Year setting to exit

Access Partition User Code + * and Partition (1 to 2)

Keypad remains in this partition until 2 minutes of no activity

Go/NoGo test (Verify signal strength)

1. Installer code 5

2. Receiver gain is reduced by 50%

3. Keypad will beep 3 times to indicate signal reception

Display Zones Hold * for 5 seconds to view all zone descriptions

View Message Hold 0 for 5 seconds