Ademco 4140XMPT2 Program Sheet

This is NOT complete, it is only here to walk through most common parts of programming!

Enter Program 1. 4140 + 8 + 0 + 0 (Display should show 00)

or

2. Power down then back up and press * and # within 1 minute

Move to Location * + Location

View Location # + Location (Display will read off one digit at a time)

Exit Program 1. *98 exits and does not allow re-entry to programming without cycling power and pressing * and #

or

2. *99 exits and does allow re-entry by Installer Code + 8 + 00

Programming can be re-entered up to 1 minute after exiting with * and # (# + 0 disables this feature)

Default Panel *97, answer YES if using alpha keypads

Compatibility

Power Ratings 750ma Aux output

2.8A Siren output

Device Address All keypads, receivers and expanders must be addressed and added in #93 menu

Address 00 to 03 are pre-programmed as alpha keypads

Address first keypad as 00 to allow entry into programming

00 Alpha Keypad (cannot be changed)

  1. to 30 Keypads, zone expanders, wireless receivers etc

Keypad Address (6128/6139/6150/6160 keypads)

  1. Remove power from keypad then power back up

  2. Hold 1 & 3 for 3 seconds, "ADDR = XX" or "XX" should appear (XX = current address)

  3. Within 10 seconds enter 00 to erase old address then enter new address (00 to 15)

  4. Press * to save and exit

(6128RF/6150RF keypads)

  1. Power keypad down then back up or remove backplate

  2. Within 30 seconds hold 1 & 3 for 3 seconds until flashing " - - 0 0"

  3. Press 1 and "cA XX" should appear (XX = current address)

  4. Enter new address (00 to 15) then * to exit back to flashing " -- 0 0"

  5. Press * to exit

Sniffer Test (Tests wireless sensors)

  1. Installer Code + # + 3

  2. Keypad displays all wireless sensors, faulting sensor removes it from list

  3. Exit with Installer Code + 1 (OFF)

Go-No Go Test (Verifies adequate RF by reducing RF receiver signal strength by 50%)

  1. Installer Code + # + 4

  2. a. Siren sounds

b. Panel may send walk test signal (If test signal was programmed)

c. "dd" appears on screen

d. Keypad will beep every 15 seconds

  1. Fault sensor, keypad should beep 3 times and display zone number,

if no beeps sound reorient or move sensor a few inches and try again

  1. Exit with Installer Code + 1 (OFF)

Partition Stuff (If system is Partitioned)

  1. Press *91

  2. Enter Partition (1 or 2)

  3. Enter location (all locations on this page marked (Partition Specific))

  4. Press *99 to return to regular panel programming

All Zone programming is done by # 93 menu, enter #93 for below menu (Click to go to section)

Tech_201000000129.gif 1 enters, 0 moves to next menu (Serial Programming)

Tech_201000000492.gif 1 enters, 0 moves to next menu (Alpha Programming)

Tech_201000000130.gif 1 enters, 0 moves to next menu (Device Programming)

Tech_201000000131.gif 1 enters, 0 moves to next menu (Relay Programming)

Tech_201000000225.gif 1 enters, 0 moves to next menu

Tech_201000000132.gif 1 exits #93 menu, 0 moves back to Zone Program

  1. = Fast

  1. = Partition 1

  2. = Partition 2

  1. = Enable

  1. = Enable

  1. = Enable

  1. = Enable

  1. nd digit = 11 (*) or 12 (#)

  1. = No Timeout

I _1 _I Medical Panic 1 = Enable

I _1 _I Police Panic

  1. = Enable

  1. = Enable

  1. = Disable

  1. = Enable

  1. to 199 Hours

  1. = Enable

  1. = Enable

  1. = Enable

(Example 9 is 09*)

(Example 1234 is 01 02 03 04) Hex B = 11 C = 12 D = 13 E = 14 F = 15

(12 digits, end with *) # + 11 = * # + 12 = # # + 13 = 2.5 second pause

(15's Default CSID to Factory)

I _1 _I Sys Shutdown 1 = Enable

I _0 _I Not Used

I _1 _I Remote Bypass

I _1 _I Remote Disarm

I _1 _I Remote Arm

I _1 _I Upload Enable

I _1 _I Download Enable

  1. to 87 zone that cannot be bypassed

  1. = Enable

  1. = Enable

  1. = Normally Closed Zones

  1. = No Pause

  1. = Enable

  1. to 14 = Rings to answer

15 = Answering Machine Over-Ride

  1. = Contact ID

  2. = Ademco High Speed

  3. = Ademco Express

  1. = Sescoa/Radionics

  1. = Contact ID

  2. = Ademco High Speed

  3. = Ademco Express

  1. = Sescoa/Radionics

I _0 _I Secondary 1 = Enable

  1. = Radionics

  1. = Enable

I _0 _I Restore 1 = Expanded

I _0 _I Bypass

I _0 _I Trouble

I _0 _I Open/Close

I _0 _I Low Battery

I _0 _I Restore 1 = Expanded

I _0 _I Bypass

I _0 _I Trouble

I _0 _I Open/Close

I _0 _I Low Battery

I _0 _I _0 _I Alarm Restoral I _0 _I _0 _I Alarm Restoral

I _0 _I _0 _I Trouble I _0 _I _0 _I Trouble

I _0 _I _0 _I Trouble Restore I _0 _I _0 _I Trouble Restore

I _0 _I _0 _I Bypass I _0 _I _0 _I Bypass

I _0 _I _0 _I Bypass Restore I _0 _I _0 _I Bypass Restore

I _0 _I _0 _I Alarm Restoral I _0 _I _0 _I Alarm Restoral

I _0 _I _0 _I Trouble I _0 _I _0 _I Trouble

I _0 _I _0 _I Trouble Restore I _0 _I _0 _I Trouble Restore

I _0 _I _0 _I Bypass I _0 _I _0 _I Bypass

I _0 _I _0 _I Bypass Restore I _0 _I _0 _I Bypass Restore

I _0 _I _0 _I Alarm Restoral

I _0 _I _0 _I Trouble

I _0 _I _0 _I Trouble Restore

I _0 _I _0 _I Bypass

I _0 _I _0 _I Bypass Restore

I _0 _I _0 _I _0 _I _0 _I _0 _I _0 _I _0 _I _0 _I 0 = Disable

1 2 3 4 5 6 7 8 1 = Enable

9 10 1 = Enable

I _0 _I _0 _I Close I _0 _I _0 _I Close

I _0 _I _0 _I Open I _0 _I _0 _I Open

I _1 _I _1 _I Low Battery I _0 _I _0 _I Low Battery

I _0 _I _0 _I Low Battery Restore I _0 _I _0 _I Low Battery Restore

I _1 _I _1 _I AC Loss I _0 _I _0 _I AC Loss

I _0 _I _0 _I AC Loss Restore I _0 _I _0 _I AC Loss Restore

I _0 _I _0 _I Test I _0 _I _0 _I Test

I _0 _I _0 _I Power I _0 _I _0 _I Power

I _1 _I _1 _I Cancel I _0 _I _0 _I Cancel

I _0 _I _0 _I Program Tamper I _0 _I _0 _I Program Tamper

I _0 _I _3 _I Hour 00 to 23

I _3 _I _0 _I Minute 00 to 59

  1. to 15 = Alarms per Armed period

I _1 _I Zone 96 Medical 1 = Enable

I _1 _I Zone 99 Police

I _1 _I Duress

  1. = allow 8 zone numbers on 1 module

prevents other polling loop expansion

1 = Continuous

1 = 15 Seconds

  1. = At Bell Timeout if Zone Restored

  2. = At Disarm

Hex B = 11, C = 12, D = 13, E = 14, F = 15

------------------------------------------------------------------------------------------------------------------------------------------------------

To access 2nd Level of Programming press *94 then enter * + 2-digits, to exit back to 1st Level Programming enter *99

------------------------------------------------------------------------------------------------------------------------------------------------------

  1. *26 First 4280 RF Receiver Select I _0 _I 0 = Disable

  1. = Enable

  1. *27 Second 4280 RF Receiver Select I _0 _I 0 = Disable

  1. = Enable

  1. *28 RF Low Battery Sound I _1 _I 0 = When Disarmed

  1. = Immediate

  1. *29 RF Low Battery Report Enable I _1 _I 0 = Disable

  1. = Enable

  1. *30 RF Receiver Check-In Interval I _0 _I _6 _I 00 = Disable Supervision

  2. to 15 x2 Hours

  1. *31 RF Transmitter Check in Interval I _1 _I _2 _I 00 = Disable Supervision

  2. to 15 x2 Hours

  1. *32 RF Receiver Type I _0 _I 0 = 4280 (5700 series wireless)

(4281 option not found on some panels) 1 = 4281 (5700 series wireless)

2 = 5881 (5800 series wireless)

  1. *33 Touch-Tone with Rotary Backup I _1 _I 0 = Disabled

  1. = Enabled

  1. *34 Communication Split Report Selection I _0 _I 0 = Disable

  1. = Alarms Primary, others Secondary

  2. = Open/Close & Test Secondary, others Primary

  1. *40 Dialer Codes 1st Digit I _ _I _ _I Armed Stay

I _ _I _ _I Time Set or Event Log Reset

I _ _I _ _I Event Log 50% & 90% Full

I _ _I _ _I Event Log Overflow

  1. *41 Dialer Codes 2nd Digit I _ _I _ _I Armed Stay

I _ _I _ _I Time Set or Event Log Reset

I _ _I _ _I Event Log 50% & 90% Full

I _ _I _ _I Event Log Overflow

  1. *43 Perm Keypad Backlight I _1 _I 0 = Disable

  1. = Enable

  1. *44 Wireless Keypad Tamper Detect I _1 _I 0 = Disable

  1. = Enable

  1. *45 Exit Delay Keypad Sounder I _1 _I 1 = Enable

0 = Disable

  1. *46 Auxiliary Output Enable I _ _I 0 = Ground Start

  1. = Open/Close Trigger

  2. = Keypad Sounding

  3. = 2-Way AAV Trigger

  1. *47 Chime on External Siren I _1 _I 0 = Disable

  1. = Enable

  1. *48 Wireless Keypad Assignment I _0 _I 0 = Disable

  1. = Partition 1 to 8 = Partition 8

  1. *49 Suppress TX Supervision Sound I _1 _I 0 = Enable

  1. = Disable

  1. *52 Send Cancel If Alarm + OFF I _1 _I 0 = Within Bell Timeout Only

  1. = No Restriction

  1. *53 Download Callback I _1 _I 0 = Callback Required

  1. = No Callback

  1. *55 Date Format Selection I _0 _I 0 = MM/DD/YY

  1. = DD/MM/YY

  1. *56 Real Time Clock Synch I _0 _I 0 = 60Hz

  1. = 50Hz

  1. *57 Enable 5800 RF Button Global Arm I _0 _I 0 = Keyfob will not Global Arm

  1. = Follows Global User Settings

  1. *58 Enable 5800 RF Button Force Bypass I _0 _I 0 = Disable

  1. = Press Arming key twice to force bypass

  1. *60 Alarm Verification (2-Way Voice) I _0 _I 0 = Not Used

1 = Use Alarm Verification

  1. *66 Silence Bells if Alarm Verification I _0 _I 0 = Disable

  1. = Enable

  1. *67 Video Alarm Verification Selection I _0 _I 0 = Disable

  1. = Use Video Alarm Verification

  1. *70 Event Log Types I _1 _I Alarm 0 = Disable Logging

I _1 _I Check 1 = Enable Logging

I _1 _I Bypass

I _1 _I Open/Close

I _1 _I System

  1. *71 12/24 Hour Time Stamp Format I _0 _I 0 = 12 Hour

  1. = 24 Hour (Military)

  1. *72 Event Log Printer On-Line I _0 _I 0 = Disable

  1. = Enable

  1. *73 Event Log Printer Baud Rate I _0 _I 0 = 1200 Baud

  1. = 300 Baud

  1. *74 Relay Timeout Minutes I _ _I _ _I _ _I 0 to 127 x2 minutes

  1. *75 Relay Timeout Seconds I _ _I _ _I _ _I 0 to 127 seconds

  1. *76 Access Control Relay for Partition I _ _I _ _I 00 = None

01 to 08 = Relay used when Code + 0

------------------------------------------------------------------------------------------------------------------------------------------------------

To access 3rd Level of Programming press *94 then enter * + 2-digits, to exit back to 2nd Level Programming enter *99

------------------------------------------------------------------------------------------------------------------------------------------------------

  1. *00 Number of Partitions I _1 _I 1 to 8 = Partition 1 to 8

2*01 Daylight Savings Time Start/End I _0 _I _4 _I Start 01 = January

I _1 _I _0 _I End 12 = December

2*02 Daylight Savings Time I _1 _I Start 1 = 1st Weekend

Start/End Weekend I _5 _I End 2 = 2nd Weekend

  1. = 3rd Weekend

  2. = 4th Weekend

  3. = Last Weekend

  4. = Next to Last Weekend

  5. = 3rd from Last Weekend

2*05 Auto Arm Delay I _0 _I _0 _I 00 = Disable

  1. to 56 minutes

  2. *06 Auto Arm Warning Period I _1 _I _5 _I 00 = Instant

  1. to 15 minutes

  2. *07 Auto Disarm Delay I _0 _I _0 _I 00 = Disabled

  1. to 56 minutes

  2. *08 Enable Force Arm for Auto Arm I _0 _I 0 = Disable

  1. = Enable

  2. *09 Enable Open/Close Rep by Exception I _0 _I 0 = Disable

  1. = Enable

  2. *10 Allow Disarming only during I _0 _I 0 = Disable

Disarm window 1 = Enable

2*11 Allow Disarm outside window I _0 _I 0 = Disable

If Alarm occurs 1 = Enable

2*13 Scheduling Related Dialer Reports I _0 _I _0 _I Early Opening Report Code

First Digit I _0 _I _0 _I Early Closing Report Code

I _0 _I _0 _I Late Opening Report Code

I _0 _I _0 _I Late Closing Report Code

I _0 _I _0 _I No Opening (Late to Open) Report Code

I _0 _I _0 _I No Closing (Late to Close) Report Code

I _0 _I _0 _I Auto Arm Failure Report Code

I _0 _I _0 _I Access Schedule Changed Report Code

2*14 Scheduling Related Dialer Reports I _0 _I _0 _I Early Opening Report Code

Second Digit I _0 _I _0 _I Early Closing Report Code

I _0 _I _0 _I Late Opening Report Code

I _0 _I _0 _I Late Closing Report Code

I _0 _I _0 _I No Opening (Late to Open) Report Code

I _0 _I _0 _I No Closing (Late to Close) Report Code

I _0 _I _0 _I Auto Arm Failure Report Code

I _0 _I _0 _I Access Schedule Changed Report Code

2*17 Number of Codes Per Partition I _9 _I _9 _I Partition 1 01 to 99

I _0 _I _1 _I Partition 2 Total must be less than or equal to 128

I _0 _I _1 _I Partition 3

I _0 _I _1 _I Partition 4

I _0 _I _1 _I Partition 5

I _0 _I _1 _I Partition 6

I _0 _I _1 _I Partition 7

I _0 _I _1 _I Partition 8

2*18 Enable Goto For This Partition I _1 _I 0 = Disable

  1. = Enable

  2. *19 Use Partition Descriptors I _1 _I 0 = Disable

  1. = Enable

  2. *20 Enable J7 Triggers by Partition I _1 _I 0 = Disable

  1. = Enable for displayed Partition

  2. *21 Enable Supervision Pulses for I _0 _I Fire 0 = Disable

Long Range Radio Trigger Outputs I _0 _I Burglary 1 = Enable

I _0 _I Silent Panic