Ademco 4140XMPT/First Alert FA1300 Programming (Under Construction)

Enter Program 1. 4140 + 8 + 0 + 0 (Display should show 00)

or Power down then back up and press * and # within 1 minute

(If exiting programming you can re-enter within 1 minute by pressing * and #)

Move to Location * + Location

View Location # + Location (Display will read off one digit at a time)

Exit Program 1. *98

or

2. *99 if needing to re-enter programming later by Code + 8 + 00

Default Panel *97

Compatibility

Power Ratings 750ma Aux output

2.8A Siren output

Device Address All keypads must be addressed and added in #93 menu

Address 00 to 03 are pre-programmed as alpha keypads

Address first keypad as 00 to allow entry into programming

00 Alpha Keypad (cannot be changed)

  1. to 30 Alpha or Fixed English keypads only

Keypad Address (6128/6150 keypads only, this panel does not support 6139 or 6160 alpha keypads)

  1. Remove power from keypad then power back up

  2. Hold 1 & 3 for 3 seconds, "ADDR = XX" or "XX" should appear (XX = current address)

  3. Within 10 seconds enter 00 to erase old address then enter new address

  4. Press * to save and exit

(6150RF keypads)

  1. Power keypad down then back up or remove backplate

  2. Within 30 seconds hold 1 & 3 for 3 seconds until flashing " - - 0 0 "

  3. Press 1 and "cA XX" should appear (XX = current address)

  4. Enter new address then * to exit back to flashing " -- 0 0 "

  5. Press * to exit

Go-No Go Test (Verifies adequate RF by reducing RF receiver signal strength by 50%)

  1. Installer Code + # + 4

  2. a. Siren sounds

b. Panel may send walk test signal (If test signal was programmed)

c. "dd" appears on screen

d. Keypad will beep every 15 seconds

  1. Fault sensor, keypad should beep 3 times and display zone number,

if no beeps sound reorient or move sensor a few inches and try again

  1. Exit with Installer Code + 1 (OFF)

Send to 1. Exit programming

Downloader 2. Press Installer or Master Code + # + 1

3. "CC" or "MODEM COMM" appears for approx. 2 minutes

4. Display will return to normal once upload is finished

Hex Program Hex A = 10 B = 11 C = 12 D = 13 E = 14 F = 15

#93 Menu

All Zone programming is done by # 93 menu, enter #93 for below menu (Click to go to section)

Tech_201000000129.gif 1 enters, 0 moves to next menu (Alpha Programming)

Tech_201000000130.gif 1 enters, 0 moves to next menu (Device Programming)

Tech_201000000131.gif 1 enters, 0 moves to next menu (Exit #93 Menu)

Tech_201000000132.gif 1 exits #93 menu, 0 moves back to Zone Program

I _ _I _ _I Zone 1 I _ _I _ _I Zone 9 01 = Entry/Exit 1

I _ _I _ _I Zone 2 I _ _I _ _I Zone 10 02 = Entry/Exit 2

I _ _I _ _I Zone 3 I _ _I _ _I Zone 11 03 = Instant

I _ _I _ _I Zone 4 I _ _I _ _I Zone 12 04 = Interior

I _ _I _ _I Zone 5 I _ _I _ _I Zone 13 05 = Day Zone

I _ _I _ _I Zone 6 I _ _I _ _I Zone 14 06 = Holdup

I _ _I _ _I Zone 7 I _ _I _ _I Zone 15 07 = Police

I _ _I _ _I Zone 8 I _ _I _ _I Zone 16 08 = Medical

09 = Fire

I _ _I _ _I Zone 17 I _ _I _ _I Zone 25

I _ _I _ _I Zone 18 I _ _I _ _I Zone 26

I _ _I _ _I Zone 19 I _ _I _ _I Zone 27

I _ _I _ _I Zone 20 I _0 _I _0 _I Not Used

I _ _I _ _I Zone 21 I _0 _I _0 _I Polling Loop Short

I _ _I _ _I Zone 22 I _0 _I _9 _I 1 & * A Panic (Fire) Key

I _ _I _ _I Zone 23 I _0 _I _8 _I 3 & # C Panic (Medical) Key

I _ _I _ _I Zone 24 I _0 _I _7 _I * & # B Panic (Police) Key

  1. = Enable

  1. = Enable

  1. = Yes

  1. = Yes

  1. = Yes

  1. = Fast

  1. = Yes

I _1 _I Zone 96 (Medical) 1 = Yes

I _1 _I Zone 99 (Police)

  1. = Yes

  1. = Yes

  1. = Yes

  1. = Yes

  1. = Touch Tone

(Example 9 is 09* )

(Example 1234 is 01 02 03 04) Hex B = 11 C = 12 D = 13 E = 14 F = 15

(12 digits, end with * ) # + 11 = * # + 12 = # # + 13 = 2.5 second pause

(12 digits, end with * ) # + 11 = * # + 12 = # # + 13 = 2.5 second pause

(12 digits, end with * ) # + 11 = * # + 12 = # # + 13 = 2.5 second pause

(15's Default CSID to Factory)

I _1 _I System Shutdown 1 = Yes

I _0 _I Not Used

I _1 _I Remote Bypass

I _1 _I Remote Disarm

I _1 _I Remote Arm

I _1 _I Upload Programming

I _1 _I Download Programming

  1. = Yes

  1. = Normally Closed Loops

  1. = 11 seconds

  2. = 30 seconds

  1. = Enable

  1. = Contact ID

  2. = Ademco High Speed

  3. = Ademco Express

  1. = Sescoa/Radionics

  1. = Contact ID

  2. = Ademco High Speed

  3. = Ademco Express

I _0 _I Secondary 1 = Yes

  1. = Sescoa

  1. = Yes

I _1 _I _1 _I Zone 1 I _0 _I _0 _I Zone 1

I _1 _I _1 _I Zone 2 I _0 _I _0 _I Zone 2

I _1 _I _1 _I Zone 3 I _0 _I _0 _I Zone 3

I _1 _I _1 _I Zone 4 I _0 _I _0 _I Zone 4

I _1 _I _1 _I Zone 5 I _0 _I _0 _I Zone 5

I _1 _I _1 _I Zone 6 I _0 _I _0 _I Zone 6

I _1 _I _1 _I Zone 7 I _0 _I _0 _I Zone 7

I _1 _I _1 _I Zone 8 I _0 _I _0 _I Zone 8

I _1 _I _1 _I Zone 9 I _0 _I _0 _I Zone 9

I _1 _I _1 _I Zone 10 I _0 _I _0 _I Zone 10

I _1 _I _1 _I Zone 11 I _0 _I _0 _I Zone 11

I _1 _I _1 _I Zone 12 I _0 _I _0 _I Zone 12

I _1 _I _1 _I Zone 13 I _0 _I _0 _I Zone 13

I _1 _I _1 _I Zone 14 I _0 _I _0 _I Zone 14

I _1 _I _1 _I Zone 15 I _0 _I _0 _I Zone 15

I _1 _I _1 _I Zone 16 I _0 _I _0 _I Zone 16

I _0 _I _0 _I Zone Restore

I _0 _I _0 _I Zone Trouble

I _0 _I _0 _I Zone Trouble Restore

I _0 _I _0 _I Zone Bypass

I _0 _I _0 _I Zone Bypass Restore

I _1 _I _1 _I Zone 17 I _0 _I _0 _I Zone 17

I _1 _I _1 _I Zone 18 I _0 _I _0 _I Zone 18

I _1 _I _1 _I Zone 19 I _0 _I _0 _I Zone 19

I _1 _I _1 _I Zone 20 I _0 _I _0 _I Zone 20

I _1 _I _1 _I Zone 21 I _0 _I _0 _I Zone 21

I _1 _I _1 _I Zone 22 I _0 _I _0 _I Zone 22

I _1 _I _1 _I Zone 23 I _0 _I _0 _I Zone 23

I _1 _I _1 _I Zone 24 I _0 _I _0 _I Zone 24

I _1 _I _1 _I Zone 25 I _0 _I _0 _I Zone 25

I _1 _I _1 _I Zone 26 I _0 _I _0 _I Zone 26

I _1 _I _1 _I Zone 27 I _0 _I _0 _I Zone 27

I _1 _I _1 _I Zone 28 I _0 _I _0 _I Zone 28

I _1 _I _1 _I Zone 29 I _0 _I _0 _I Zone 29

I _1 _I _1 _I Zone 30 I _0 _I _0 _I Zone 30

I _1 _I _1 _I Zone 31 I _0 _I _0 _I Zone 31

I _1 _I _1 _I Zone 32 I _0 _I _0 _I Zone 32

I _0 _I _0 _I Zone Restore

I _0 _I _0 _I Zone Trouble

I _0 _I _0 _I Zone Trouble Restore

I _0 _I _0 _I Zone Bypass

I _0 _I _0 _I Zone Bypass Restore

I _1 _I _1 _I Zone 33 I _0 _I _0 _I Zone 33

I _1 _I _1 _I Zone 34 I _0 _I _0 _I Zone 34

I _1 _I _1 _I Zone 35 I _0 _I _0 _I Zone 35

I _1 _I _1 _I Zone 36 I _0 _I _0 _I Zone 36

I _1 _I _1 _I Zone 37 I _0 _I _0 _I Zone 37

I _1 _I _1 _I Zone 38 I _0 _I _0 _I Zone 38

I _1 _I _1 _I Zone 39 I _0 _I _0 _I Zone 39

I _1 _I _1 _I Zone 40 I _0 _I _0 _I Zone 40

I _1 _I _1 _I Zone 41 I _0 _I _0 _I Zone 41

I _1 _I _1 _I Zone 42 I _0 _I _0 _I Zone 42

I _1 _I _1 _I Zone 43 I _0 _I _0 _I Zone 43

I _1 _I _1 _I Zone 44 I _0 _I _0 _I Zone 44

I _1 _I _1 _I Zone 45 I _0 _I _0 _I Zone 45

I _1 _I _1 _I Zone 46 I _0 _I _0 _I Zone 46

I _1 _I _1 _I Zone 47 I _0 _I _0 _I Zone 47

I _1 _I _1 _I Zone 48 I _0 _I _0 _I Zone 48

I _0 _I _0 _I Zone Restore

I _0 _I _0 _I Zone Trouble

I _0 _I _0 _I Zone Trouble Restore

I _0 _I _0 _I Zone Bypass

I _0 _I _0 _I Zone Bypass Restore

I _1 _I _1 _I Zone 49 I _0 _I _0 _I Zone 49

I _1 _I _1 _I Zone 50 I _0 _I _0 _I Zone 50

I _1 _I _1 _I Zone 51 I _0 _I _0 _I Zone 51

I _1 _I _1 _I Zone 52 I _0 _I _0 _I Zone 52

I _1 _I _1 _I Zone 53 I _0 _I _0 _I Zone 53

I _1 _I _1 _I Zone 54 I _0 _I _0 _I Zone 54

I _1 _I _1 _I Zone 55 I _0 _I _0 _I Zone 55

I _1 _I _1 _I Zone 56 I _0 _I _0 _I Zone 56

I _1 _I _1 _I Zone 57 I _0 _I _0 _I Zone 57

I _1 _I _1 _I Zone 58 I _0 _I _0 _I Zone 58

I _1 _I _1 _I Zone 59 I _0 _I _0 _I Zone 59

I _1 _I _1 _I Zone 60 I _0 _I _0 _I Zone 60

I _1 _I _1 _I Zone 61 I _0 _I _0 _I Zone 61

I _1 _I _1 _I Zone 62 I _0 _I _0 _I Zone 62

I _1 _I _1 _I Zone 63 I _0 _I _0 _I Zone 63

I _1 _I _1 _I Zone 64 I _0 _I _0 _I Zone 64

I _0 _I _0 _I Zone Restore

I _0 _I _0 _I Zone Trouble

I _0 _I _0 _I Zone Trouble Restore

I _0 _I _0 _I Zone Bypass

I _0 _I _0 _I Zone Bypass Restore

I _0 _I _0 _I Not Used I _0 _I _0 _I Not Used

I _0 _I _0 _I Not Used I _0 _I _0 _I Not Used

I _0 _I _0 _I Not Used I _0 _I _0 _I Not Used

I _0 _I _0 _I Not Used I _0 _I _0 _I Not Used

I _0 _I _0 _I Not Used I _0 _I _0 _I Not Used

I _0 _I _0 _I Not Used I _0 _I _0 _I Not Used

I _0 _I _0 _I Zone 87 4284 Voice Module Supervisory I _0 _I _0 _I Zone 87

I _0 _I _0 _I Zone 88 Receiver Not Hearing Transmitter I _0 _I _0 _I Zone 88

I _0 _I _0 _I Zone 89 Receiver not Responding I _0 _I _0 _I Zone 89

I _0 _I _0 _I Zone 90 Receiver not hearing Transmitter I _0 _I _0 _I Zone 90

I _0 _I _0 _I Zone 91 Receiver not Responding I _0 _I _0 _I Zone 91

I _1 _I _1 _I Duress I _0 _I _0 _I Duress

I _0 _I _0 _I Zone 97 Polling Loop Short I _0 _I _0 _I Zone 97

I _1 _I _1 _I Zone 95 1 & * A Fire Panic Key I _0 _I _0 _I Zone 95

I _1 _I _1 _I Zone 96 3 & # C Medical Panic Key I _0 _I _0 _I Zone 96

I _1 _I _1 _I Zone 99 * & # B Police Panic Key I _0 _I _0 _I Zone 99

I _0 _I _0 _I Zone Restore

I _0 _I _0 _I Zone Trouble

I _0 _I _0 _I Zone Trouble Restore

I _0 _I _0 _I Zone Bypass

I _0 _I _0 _I Zone Bypass Restore

I _0 _I _0 _I _0 _I _0 _I _0 _I _0 _I _0 _I _0 _I 0 = Disable 1 = Enable

I _0 _I _0 _I 0 = Disable 1 = Enable

I _0 _I _0 _I Close I _0 _I _0 _I Close

I _0 _I _0 _I Open I _0 _I _0 _I Open

I _1 _I _1 _I Low Battery I _0 _I _0 _I Low Battery

I _0 _I _0 _I Low Battery Restore I _0 _I _0 _I Low Battery Rest

I _1 _I _1 _I AC Loss I _0 _I _0 _I AC Loss

I _0 _I _0 _I AC Loss Restore I _0 _I _0 _I AC Loss Rest

I _0 _I _0 _I Test I _0 _I _0 _I Test

I _0 _I _0 _I Power I _0 _I _0 _I Power

I _1 _I _1 _I Cancel I _0 _I _0 _I Cancel

I _0 _I _0 _I Program Tamper I _0 _I _0 _I Program Tamp

Hex B = 11, C = 12, D = 13, E = 14, F = 15

------------------------------------------------------------------------------------------------------------------------------------------------------

To access 2nd Level of Programming press *94 then enter * + 2-digits, to exit back to 1st Level Programming enter *99

------------------------------------------------------------------------------------------------------------------------------------------------------

  1. *33 Touch-Tone W/Rotary Backup I _1 _I 0 = Disable

  1. = Enable

  1. *40 Armed Stay Report 1st Digit I _0 _I _0 _I Armed Stay

I _0 _I _0 _I Time/Date set or Event Log reset

I _0 _I _0 _I Event Log 50% & 90% Full

I _0 _I _0 _I Event Log Overflow

  1. *41 Armed Stay Report 2nd Digit I _0 _I _0 _I Armed Stay

I _0 _I _0 _I Time/Date set or Event Log reset

I _0 _I _0 _I Event Log 50% & 90% Full

I _0 _I _0 _I Event Log Overflow

  1. *43 Enable Perm Backlight I _0 _I 0 = Disable

  1. = Enable

  1. *45 Enable Console Exit Beeps I _1 _I 0 = Disable

  1. = Enable

  1. *46 Aux Output Enable I _0 _I 0 = Ground Start

  1. = O/C Trigger

  2. = Console Sound

  1. *53 Download Callback I _1 _I 0 = Yes

  1. = No Callback

  1. *70 Event Log Types I _1 _I Alarm 0 = Disable

I _1 _I Check 1 = Enable

I _1 _I Bypass

I _1 _I Open/Close

I _1 _I System

  1. *71 12/24 Hour Time Stamp Format I _0 _I 0 = 12 Hour

  1. = 24 Hour

  1. *72 Event Log Printer Online I _0 _I 0 = Disable

  1. = Enable

  1. *73 Printer Baud Rate I _0 _I 0 = 1200 Baud

  1. = 300 Baud

------------------------------------------------------------------------------------------------------------------------------------------------------

To access 3rd Level of Programming press *94 then enter * + 2-digits, to exit back to 2nd Level Programming enter *99

------------------------------------------------------------------------------------------------------------------------------------------------------

  1. *18 Enable Goto For This Partition I _0 _I Partition 1 0 = Disable

I _0 _I Partition 2 1 = Enable

I _0 _I Partition 3

I _0 _I Partition 4

I _0 _I Partition 5

I _0 _I Partition 6

I _0 _I Partition 7

I _0 _I Partition 8

2*19 Use Partition Descriptors I _0 _I Partition 1 0 = Disable

I _0 _I Partition 2 1 = Enable

I _0 _I Partition 3

I _0 _I Partition 4

I _0 _I Partition 5

I _0 _I Partition 6

I _0 _I Partition 7

I _0 _I Partition 8

2*20 Enable J7 Triggers By Partition I _1 _I 0 = Disable

  1. = Enable