Ademco Lynx/First Alert ReadyGuard Program Sheet

Power Ratings 30mA - Piezo output terminals 10 & 11

120mA - Bell output terminals 11 & 12

Enter Program 4112 + 8 + 0 + 0 (Display should show 20)

or Power down then back up and press * and # within 1 minute

(If exiting programming you can re-enter within 1 minute by pressing * and #)

Exit Program 1. *98 OR 2. *99 if needing to re-enter programming later by Code + 8 + 00

Move to Location * + Location

View Location # + Location (Display will read off one digit at a time)

Sniffer Test (Tests wireless sensors)

  1. Installer Code + # + 3

  2. Keypad displays all wireless sensors, faulting sensor removes it from list

  3. Exit with Installer Code + 1 (OFF)

Go-No Go Test (Verifies adequate RF by reducing receiver signal strength by 50%)

  1. Installer Code + # + 8

  2. a. Siren sounds

b. Panel may send walk test signal (If test signal was programmed)

c. "dd" appears on screen

d. Keypad will beep every 15 seconds

  1. Fault sensor, keypad should beep 3 times and display zone number,

if no beeps sound reorient or move sensor a few inches and try again

  1. Exit with Installer Code + 1 (OFF)

  1. = Enable

  1. = Backlight Off after 10 seconds

  1. = Enable

(5827, 5827BD keypads and 5804BD Keyfobs) 01 to 31

  1. = G 7 = H 8 = I 9 = J #10 = K

#11 = L #12 = M #13 = N #14 = O #15 = P

  1. = Enable zones to chime in *81 Zone List 3

  1. = Enable

  1. = January 08 = August

  2. = February 09 = September

  3. = March #10 = October

  4. = April #11 = November

  5. = May #12 = December

  6. = June

Start/End Weekend Number 2 = 2nd Weekend

3 = 3rd Weekend

4 = 4th Weekend

5 = Last Weekend

6 = Next to Last Weekend

  1. = 3rd from Last Weekend

  1. = 1 per Arming period

  1. = Enable

  1. = 4 minutes

  2. = 8 minutes

  3. = 12 minutes

  4. = 16 minutes

I _ 1 _I Quick Exit 1 = Enable

  1. = 1/2 second siren if armed by keypad or RF Keyfob/Keypad

  2. = 1/2 second siren if armed by RF keyfob/Keypad

  1. = Enable

(If 9 is needed to dial add here)

End Phone with * # + 11 = * # + 12 = # # + 13 = 2 second pause

(Hex B = #+11 C = #+12 D = #+13 E = #+14 F = #+15)

  1. = DTMF Dial

  2. = Pulse Dial, CS on Watts Line

  3. = DTMF Dial, CS on Watts Line

I _ 7 _I Secondary 1 = 3/1, 4/1 Radionics Standard

2 = 4/2 Ademco L/S Standard

3 = 4/2 Radionics Standard

6 = 4/2 Ademco Express

7 = Contact ID

8 = 3/1, 4/1 Ademco L/S Expanded

9 = 3/1, 4/1 Radionics Expanded

To Primary Phone To Secondary Phone

  1. = Alarms, Restore, Cancel All Other Reports

  2. = All Reports except Open/Close, Test Open/Close, Test

  3. = Alarms, Restore, Cancel All Reports

  4. = All Reports except Open/Close, Test All Reports

  5. = All Reports (Dual Reporting) All Reports

To Primary Phone To Pager (Secondary)

  1. = All reports except Open/Close (Pager) Alarms, Open/Close/Trouble

  2. = All reports Alarms, Troubles

  3. = All reports Alarms, Open/Close, Troubles

  4. = All reports except Open/Close Open/Close for Users 5 to 8 or wireless arm/disarm

keyfob zones 34-41, users 1 to 4 and Keyfobs

26-33 do not send open/close reports

  1. = Enable

  1. = 24 Hours

  2. = Weekly

  3. = Monthly

(sends after exit program 1 = 6 Hours

mode or after downloading) 2 = 12 Hours

3 = 18 Hours

  1. = Sescoa

1. Enter Zone to program (01 to 99) or 00 to exit (* for next, 00 to exit)

Tech_201000000261.gif Hardwire Zone Zone 01

Wireless Zones Zones 02 to 25

Keyfob Zones Zones 26 to 41

Duress Code Zone 92

Fire Panic Zone 95

Medical Panic Zone 96

Police Panic Zone 99

Lynx Defaults Zone 2 = Delay Zone on Loop 2, Voice description = "Front Door"

Zone 3 = Delay Zone on Loop 2, Voice description = "Back Door Door"

Zone 4 = Instant Zone on Loop 2, Voice description = "Window"

Zone 5 = Interior on Loop 1, Voice description = "Motion Detector"

Zone 26 = 21 Arm Away Loop 3 Zone 30 = 21 Arm Away Loop 3

Zone 27 = 22 Disarm Loop 2 Zone 31 = 22 Disarm Loop 2

Zone 28 = 20 Arm Stay Loop 4 Zone 32 = 20 Arm Stay Loop 4

Zone 29 = 23 No Alarm Loop 1 Zone 33 = 23 No Alarm Loop 1

2. Enter Zone Type then * for next, # for previous menu

Tech_201000000262.gif 00 = Zone Disabled/Deleted 08 = 24 hour Aux/Medical

  1. = Delay Zone 09 = Fire

  2. = Secondary Delay Zone 10 = Interior Delay

  3. = Perimeter/Instant 20 = Arm-Stay

  4. = Interior Follower/Motions 21 = Arm-Away

  5. = Trouble by Day/Alarm by Night 22 = Disarm

  6. = 24 hour Silent/Holdup 23 = No Alarm Response

  7. = 24 hour Police Panic 24 = Silent Burglary

3. Enter 10 for Report Code then * for next, # for previous menu

Tech_201000000263.gif

If programming Panics or Duress display will move back to step 1, sensors continue to step 4

4. Enter RF Loop Type then * for next, # for previous menu

Tech_201000000264.gif 3 = RF (Door/Motions/Glassbreaks/Smokes)

4 = UR (some Remote Panic Buttons)

5 = BR (Keyfobs and Panic Buttons)

5. Enter Loop Number (0 to 4) (* for next, # for previous menu)

Tech_201000000265.gif (0 displays "F" delete sensor screen, see end of this section)

Door Switch External wired connector = Loop 1

Internal reed switch = loop 2

Glassbreak Loop 1

Smoke Detectors Loop 1

Motions Loop 1

Keyfobs Bottom Right Button = Loop 1

(Each button is 1 zone) Top Right Button = Loop 2

Top Left Button = Loop 3

Bottom Left Button = Loop 4

5a. If this appears sensor has been previously learned

Tech_201000000266.gif

6. Press 1 to enter Serial Number, 0 skips to Voice Program (* for next, # for previous menu)

Tech_201000000267.gif

7. If 1 is pressed enter Serial Number now then * (* for next, # skips back to step 6)

Tech_201000000268.gif

8. Serial Number displays, press * to accept, # backs up to step 7

Tech_201000000269.gif

9. Press 1 to enter Zone Descriptor, 0 skips to next zone

Tech_201000000272.gif

10. Enter 1st word with # + 2-digit word

Tech_201000000273.gif 6 saves and moves to step 11 (Keypad speaks each word as entered)

  1. saves and moves to next zone

11. Enter 2nd word with # + 2-digit word

Tech_201000000274.gif 6 saves and moves to step 12 (Keypad speaks each word as entered)

8 saves and moves to next zone

12. Enter 3rd word with # + 2-digit word

Tech_201000000275.gif 6 or 8 saves new Voice Descriptor (Keypad speaks new Voice Descriptor)

and moves to next Zone

00 1/2 sec pause 14 Fire 28 Motion 42 Window

  1. Alarm 15 Floor 29 Office 43 Yard

  2. Attic 16 Front 30 Patio 44 Zones

  3. Baby 17 Garage 31 Pool 45 1st

  4. Back 18 Gun 32 Room 46 2nd

  5. Basement 19 Hall 33 Shed 47 3rd

  6. Bathroom 20 Inside 34 Shop 70 Custom Word 1

  7. Bedroom 21 Kitchen 35 Side 71 Custom Word 2

08 Check 22 Laundry 36 Sliding 72 Custom Word 3

09 Den 23 Library 37 Smoke 73 Custom Word 4

10 Detector 24 Living 38 Storage 74 Custom Word 5

11 Dining 25 Main 39 System 99 Blank

12 Door 26 Master 40 Upstairs

13 Emergency 27 Message 41 Utility

13. Enter next Zone to program (01 to 99) or 00 to exit

Tech_201000000276.gif

Delete Sensor

1. At "A" Zone Number (step 1) screen enter zone to delete (01 to 41) then *

2. At "B" Zone Type (step 2) screen enter 00 then *

or enter 0 at "E" Loop Number screen (step 5) then *

3. Press * until "F" Delete Sensor screen appears

Tech_201000000277.gif

4. If 00 was entered at Zone Type (B) screen press 1 to delete sensor and move to next sensor programming

if 0 was entered at Loop Number (E2 or E2L) screen press 1 to delete only the serial number and move to 1C screen

  1. = RF Jam Detect, no Report

  2. = RF Jam + Report

I _ 0 _I Stay

Example: to open garage door

  1. Select Device 01 in step 2

  2. Select 1 in step 3 to close for 2 seconds to activate X-10 PowerFlash at garage door opener

  3. Select 2 in step 4 to enable keyfob button fault to activate X-10 PowerFlash

  4. Select a Zone List which has the keyfob button entered (programmed in *81)

  5. Bypass steps 6 and 7, program keyfob button as Type 23 (No Alarm Response)

Note: To turn a lamp on and off with keyfob 2 buttons must be used, one for ON and one for OFF

1. Press 0 to exit or 1 to enter *80 programming

Tech_201000000278.gif

2. Enter 2-digit X-10 Device number (01 to 08) (* for next, 00 to exit)

Tech_201000000279.gif Set by X-10 module number dials

3. Enter what X-10 device will do or 0 to skip (* for next, # for previous)

Tech_201000000280.gif 0 = No Response/Skip

  1. = Close for 2 seconds

  2. = Close and stay closed

  3. = Pulse On and Off

4. Enter START Event Type (Type of event to trigger device) (* for next, # for previous)

Tech_201000000281.gif 0 = Not Used/Skip

  1. = Alarm

  2. = Fault (Zone or Keyfob button)

  3. = Trouble

5. Enter START Zone List (List programmed in *81) (* for next, # for previous)

Tech_201000000282.gif 0 = Not Used/Skip

  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

6. Enter START Zone Type (Optional) (* for next, # for previous)

Tech_201000000283.gif 00 = Not Used/Skip 22 = Disarming

  1. = Delay Zone 31 = End of Exit Time

  2. = Secondary Delay Zone 32 = Start of Entry Time

  3. = Perimeter/Instant 33 = Any Burglar Alarm

  4. = Interior Follower/Motions 36 = At Bell Timeout or Disarm

  5. = Trouble by Day/Alarm by Night 38 = Chime

  6. = 24 hour Silent/Holdup 39 = Any Fire Alarm

  7. = 24 hour Police Panic 40 = Bypassing

08 = 24 hour Aux/Medical 42 = System Low Battery

09 = Fire 43 = Communication Failure

10 = Interior Delay 52 = Kissoff

20 = Arm-Stay 58 = Duress

21 = Arm-Away

7. Enter STOP Zone List (List programmed in *81) (* for next, # for previous)

Tech_201000000284.gif 0 = Not Used/Skip

  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

8. Enter STOP Zone Type (Optional) (* for next, # for previous)

Tech_201000000285.gif (see above Zone Types)

9. Enter next 2-digit Device number (01 to 08) or 00 to exit

Tech_201000000279.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. Press 1 to enter zone list programming, 0 to exit

Tech_201000000286.gif

2. Enter Zone List to program (* for next, 00 exits)

Tech_201000000287.gif Zone List 1 = X-10

Zone List 2 = X-10

Zone List 3 for Chime By Zone *26

3. Enter Zone to add to Zone List then * then 00 for step 4 (* for next, 00 exits)

Tech_201000000288.gif Multiple Zones can be added (example: 01* 03* 25*etc)

4. To delete this Zone List press 1, to skip to step 5 press 0 (* for next, 00 exits)

Tech_201000000289.gif

5. To delete Zone in this List press 1, to skip to step 6 press 0 (* for next, 00 exits)

Tech_201000000290.gif

5a. If 1 was selected enter Zone to delete then *, end with 00

Tech_201000000291.gif Multiple Zones can be deleted (example: 01* 03* 25*etc)

6. Enter next Zone List to program or 00 to exit

Tech_201000000287.gif

  1. Press 1 to enter mode programming, 0 to exit

Tech_201000000292.gif

2. Enter Zone to add Voice Description (01 to 99) (* for next, 00 exits)

Tech_201000000293.gif

3. Enter 1st word with # + 2-digit Descriptor

Tech_201000000302.gif 6 saves and moves to step 4 (Keypad speaks each word as entered)

8 saves and moves to next zone

4. Enter 2nd word with # + 2-digit Descriptor

Tech_201000000294.gif 6 saves and moves to step 5 (Keypad speaks each word as entered)

8 saves and moves to next zone

5. Enter 3nd word with # + 2-digit Descriptor

Tech_201000000295.gif 6 or 8 to save and finish (Keypad speaks entire Voice Descriptor)

6. Enter next Zone to add Voice Description (01 to 99) or 00 to exit

Tech_201000000293.gif

00 1/2 sec pause 14 Fire 28 Motion 42 Window

  1. Alarm 15 Floor 29 Office 43 Yard

  2. Attic 16 Front 30 Patio 44 Zones

  3. Baby 17 Garage 31 Pool 45 1st

  4. Back 18 Gun 32 Room 46 2nd

  5. Basement 19 Hall 33 Shed 47 3rd

  6. Bathroom 20 Inside 34 Shop 70 Custom Word 1

  7. Bedroom 21 Kitchen 35 Side 71 Custom Word 2

08 Check 22 Laundry 36 Sliding 72 Custom Word 3

09 Den 23 Library 37 Smoke 73 Custom Word 4

10 Detector 24 Living 38 Storage 74 Custom Word 5

11 Dining 25 Main 39 System 99 Blank

12 Door 26 Master 40 Upstairs

13 Emergency 27 Message 41 Utility

  1. Press 1 to enter mode programming, 0 to exit

Tech_201000000296.gif

2. Enter Custom Word to program (70 to 74) (* for next, 00 exits)

Tech_201000000303.gif

Tech_201000000297.gif

3. Press # and after 3rd beep speak Voice Descriptor (Recording length is 1.5 seconds)

4. # to re-record, 6 saves and move to step 2 then 0 to exit

(For Macros see "Basic Commands") 1 = Aux key sends message to Pager

(For PIN's, 800 blocks etc * = # + 11, # = # + 12, 2 second pause = # + 13)

(Logs into Event Buffer) 1 = Logs Alarm/Restore

2 = Logs Trouble/Restore

4 = Logs Bypass/Restore

  1. = Open/Close

#15 = Logs all

  1. = Unlimited per Armed period

  1. = Last digit flexible

  2. = Last 2-digits flexible

  3. = Last 3-digits flexible

  1. to 14 = Rings before answer

15 = Answering Machine over-ride