Ademco Via-30PSE Program Sheet

Enter Program 1. 4111 + 8 + 0 + 0 (Display should show 00)

or

2. Power down then back up and press * and # within 1 minute

Move to Location * + Location

View Location # + Location (Display will read off one digit at a time)

Exit Program 1. *98 exits and does not allow re-entry to programming without cycling power and pressing * and #

or

2. *99 exits and does allow re-entry by Installer Code + 8 + 00

Programming can be re-entered up to 1 minute after exiting with * and # (# + 0 disables this feature)

Default Panel *97

Compatibility

Power Ratings 500ma Aux output

2A Siren output

Keypad Address (6128/6139/6150/6160 keypads)

  1. Remove power from keypad then power back up

  2. Hold 1 & 3 for 3 seconds, "ADDR = XX" or "XX" should appear (XX = current address)

  3. Within 10 seconds enter 00 to erase old address then enter new address (31)

  4. Press * to save and exit

(6150RF keypads)

  1. Power keypad down then back up

  2. Hold 1 & 3 for 3 seconds until flashing " - - 0 0" (if "DA" shows power down then up again)

  3. Press 1 and "cA XX" should appear (XX = current address)

  4. Press 31 then * to exit back to flashing " -- 0 0"

4. Press * to exit

Sniffer Test (Tests wireless sensors)

  1. Installer Code + # + 3

  2. Keypad displays all wireless sensors, faulting sensor removes it from list

  3. Exit with Installer Code + 1 (OFF)

Go-No Go Test (Verifies adequate RF by reducing receiver signal strength by 50%)

  1. Installer Code + # + 4

  2. a. Siren sounds

b. Panel may send walk test signal (If test signal was programmed)

c. "dd" appears on screen

d. Keypad will beep every 15 seconds

  1. Fault sensor, keypad should beep 3 times and display zone number,

if no beeps sound reorient or move sensor a few inches and try again

  1. Exit with Installer Code + 1 (OFF)

Hex Program Hex A = # + 10 B = # + 11 C = # + 12 D = # + 13 E = # + 14 F = # + 15

  1. = Enable

  1. = 5700 wireless with 4281 Receiver

Panel treats 5700 wireless as hardwire zones 2 = 5800 wireless with 5881 receiver

4281L receiver adds 4 zones (Zones 10 to 13) 4 = 5800 wireless RF Jamming

4281M and 4281H add 8 zones (Zones 10 to 17) (1 available on Via-30PSE v14 and below)

(4 available on Via-30PSE v13 and above)

  1. = Enable

(5700 wireless, 5804BD keyfob and 5827BD Keypad) 01 to 31

  1. = 4219 8-Zone Expander

  2. = 4229 8-Zone Expander/Relay

  3. = 4204 Relay Module

  1. st digit = 1 to 9

  2. nd digit = # + 11 = * or # + 12 = #

  1. = Enable

  1. = Enable

  1. = No Fire Timeout

  1. = 4 minutes

  2. = 8 minutes

  3. = 12 minutes

  4. = 16 minutes

Exit Delay = Entry + 15 seconds 1 = 20 seconds

2 = 30 seconds

3 = 45 seconds

4 = 60 seconds

  1. = 90 seconds

  1. = Enable

End Phone with * # + 11 = * # + 12 = # # + 13 = 2.5 second pause

(Hex B = #+11 C = #+12 D = #+13 E = #+14 F = #+15)

  1. = DTMF Dial

  2. = Pulse Dial, CS on Watts Line

  3. = DTMF Dial, CS on Watts Line

  1. = 3/1, 4/1 Radionics Standard

  2. = 4/2 Ademco L/S Standard

  3. = 4/2 Radionics Standard

6 = 4/2 Ademco Express

7 = Contact ID

8 = 3/1, 4/1 Ademco L/S Expanded

9 = 3/1, 4/1 Radionics Expanded

To Primary Phone To Secondary Phone

0 = All Reports Backup Only

  1. = Alarms, Restore, Cancel All Other Reports

  2. = All Reports except Open/Close, Test Open/Close, Test

  3. = Alarms, Restore, Cancel All Reports

  4. = All Reports except Open/Close, Test All Reports

  5. = All Reports (Dual Reporting) All Reports

  6. = All reports except Open/Close Alarms, Open/Close, Troubles

  7. = All reports Alarms, Troubles

  8. = All reports Alarms, Open/Close, Troubles

  9. = All reports except Open/Close Alarms, Open/Close for Users 5-25, Troubles

  1. = Enable

  1. = 24 Hours

  2. = Weekly

  3. = Monthly

  1. = Enable

  1. = Enable

  2. = Enable for RF Arming

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

1. Depending on version of system one of these may appear

(If "Program Tool?" press 0, if "Set to Confirm?" shows press 1)

Tech_201000000170.gif Tech_201000000171.gif

2. Enter Zone to program (01 to 96) (* for next, # for previous menu)

Tech_201000000090.gif

Hardwire Zone 04 and 06

Smoke Detectors Zone 05 only

4219/4229 Zone Expander Zone 10 to 17

Police Panic Zone 07

Duress Zone 08

Receiver Tamper/Trouble Zone 09

Wireless Zone 10 to 39 (Depends on receiver capacity)

Fire Panic Zone 95

Medical Panic Zone 96

3. This shows current summary of Zone programming (* for next, # for previous menu)

Tech_201000000091.gif

4. Enter Zone Type (* for next, # for previous menu)

Tech_201000000092.gif 00 = Zone Disabled 08 = 24 hour Aux/Medical

  1. = Delay Zone 09 = Fire

  2. = Do not Use 10 = Interior Delay

  3. = Perimeter/Instant 20 = Arm-Stay (RF only)

  4. = Interior Follower/Motions 21 = Arm-Away (RF only)

  5. = Trouble by Day/Alarm by Night 22 = Disarm (RF only)

  6. = 24 hour Silent/Holdup 23 = No Alarm Response

  7. = 24 hour Police Panic

5. Enter Report Code (* for next, # for previous menu)

Tech_201000000094.gif (10 in first section gives a report of A0)

Hardwire Zones will advance to step 9, for Wireless Zones continue

(If it doesn't go to next steps check if Receiver has been programmed in *22)

6. Enter type of Sensor

Tech_201000000095.gif 3 for Supervised RF (most sensors are RF)

4 for Un-Supervised RF

5 RF Button Type (Keyfobs/Panics etc)

(New versions may skip step 7 and move to step 8, learn Loop number after learning sensor)

7. Enter Loop number (some older systems) (* for next, # for previous menu)

Tech_201000000096.gif

Door Switch Internal switch Loop 2, external hardwire sensor Loop 1

Glassbreak Loop 1

Smoke Detectors Loop 1

Motions Loop 1

Keyfobs Bottom Right Button = Loop 1

(Each button counts as 1 zone) Top Right Button = Loop 2

Top Left Button = Loop 3

Bottom Left Button = Loop 4

8. Serial Number Programming

Tech_201000000172.gif

Press 1 and either enter serial number or trip sensor twice, 1st to learn, 2nd to confirm

Note: Serial numbers found on sticker on of sensor, if not, learn by tripping sensor

Tech_201000000173.gif This shows ready to learn

Tech_201000000174.gif This shows Serial Number either manually entered or learned

Tech_201000000175.gif This shows sensor was confirmed by activating twice

9. This is the new programming of sensor (* for next, # for previous menu)

Tech_201000000099.gif

10. 0 or * returns to beginning, 1 programs alpha descriptors

Tech_201000000100.gif

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

1. Press 1 here to allow confirming sensor after serial number input

Tech_201000000170.gif

2. Enter Zone to program (01 to 96) then *

Tech_201000000176.gif

3. Enter Zone Type (Display moves to Report Code, # starts over)

Tech_201000000177.gif 00 = Zone Disabled 08 = 24 hour Aux/Medical

  1. = Delay Zone 09 = Fire

  2. = Do not Use 10 = Interior Delay

  3. = Perimeter/Instant 20 = Arm-Stay (RF only)

  4. = Interior Follower/Motions 21 = Arm-Away (RF only)

  5. = Trouble by Day/Alarm by Night 22 = Disarm (RF only)

  6. = 24 hour Silent/Holdup 23 = No Alarm Response

  7. = 24 hour Police Panic

4. Display moves to Report Code, if needed enter 10 (Display moves to Sensor Type, # starts over)

Tech_201000000178.gif

A key moves left through fields if needed

B key moves right through fields if needed

C key copies previous Zone attributes

Hardwired Zones automatically skip to step 9, Wireless Zones continue with step 5

5. Enter Wireless sensor type then *

Tech_201000000179.gif 3 = Supervised RF (Doors, Motions, Smokes)

4 = Un-Supervised RF (some Panics)

5 = RF Button Type RF (Keyfobs/Panics)

6. If Wireless enter Serial Number or trip sensor twice (Keypad will beep twice as Sensor learns)

Tech_201000000180.gif

Tech_201000000181.gif

7. Enter Loop only if manually entering Serial Number (* for next, # for previous menu)

Tech_201000000182.gif

8. If "Set to Confirm" was selected while first entering *58 this will appear

Tech_201000000183.gif Trip sensor again to confirm

Tech_201000000184.gif This shows panel and sensor serials match

9. Enter next sensor or 00 then * or # to exit *58 menu

Tech_201000000185.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

I _ 0 _I Exit Alarm

I _ 0 _I Stay

RF Low Bat, Bypass

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. Enter Relay to program (01 to 04) (* for next, 00 to exit)

    Tech_201000000160.gif

  2. This shows summary of current Relay START programming (* for next, # for previous menu)

    Tech_201000000161.gif
(What starts the Relay)

  1. This shows summary of current Relay STOP programming (* for next, # for previous menu)

    Tech_201000000162.gif
(What stops the Relay)

  1. Enter what Relay will do when activated (* for next, # for previous menu)

    Tech_201000000163.gif
0 = No Response (or skip)

  1. = Close for 2 seconds

  2. = Close and stay closed

  3. = Continuous Pulse On/Off

5. Enter what will start the Relay (optional) (* for next, # for previous menu)

Tech_201000000164.gif 0 = Not Used (or skip)

  1. = on an Alarm

  2. = on a Zone Fault (or Keyfob button)

  3. = on a Trouble

6. Enter Zone List from *81 which STARTS Relay (optional) (* for next, # for previous menu)

Tech_201000000165.gif 0 = Not Used (or skip)

  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

7. Enter Zone Type that will START the Relay (optional) (* for next, # for previous menu)

Tech_201000000166.gif 00 = Not Used (or skip) 31 = End of Exit Time

  1. = Entry/Exit Zone 32 = Start of Entry Time

03 = Perimeter/Instant Zone 33 = Any Burglar Alarm

04 = Interior Follower/Motions 34 = Code + # + 7 Key Entry

05 = Trouble by Day/Alarm by Night 35 = Code + # + 8 Key Entry

06 = 24 hour Silent/Holdup 36 = Bell Timeout or Disarm

07 = 24 hour Police Panic 38 = Chime

08 = 24 hour Aux/Medical 39 = Any Fire Alarm

09 = Fire 40 = Bypassing

10 = Interior Delay 41 = AC Power Failure

20 = Arm-Stay 42 = System Low Battery

21 = Arm-Away 58 = Duress

22 = Disarming

8. Enter Zone List that will STOP the Relay (optional) (* for next, # for previous menu)

Tech_201000000167.gif 0 = Not Used

  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

9. Enter Zone Type that will STOP the Relay (optional) (* for next, # for previous menu)

Tech_201000000110.gif

10. This shows summary of new Relay START programming (* for next, # for previous menu)

Tech_201000000168.gif

11. This shows summary of new Relay STOP programming (* for next, # for previous menu)

Tech_201000000169.gif

12. Enter next Relay to program or 00 to exit

Tech_201000000160.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. Enter Zone List to program (01 to 03) or 00 to Quit (* for next, # for previous menu)

    Tech_201000000115.gif

  2. Enter Zone Number to add to List (01, 02 etc) or 00 to Quit (* for next, # for previous menu)

    Tech_201000000116.gif
Multiple Zones can be added (Example: 01* 03* 25* etc)

  1. If deleting a Zone List enter (01 to 03) or 0 to skip (* for next, # for previous menu)

    Tech_201000000117.gif

  2. If deleting Zone within Zone List enter 1 or 0 to skip (* for next, # for previous menu)

    Tech_201000000118.gif

4a. If 1 was entered from previous step enter here then 00 (* for next, # for previous menu)

Tech_201000000119.gif Multiple Zones can be deleted (Example: 01* 03* 25* etc)

  1. Enter next Zone List to program or 00 to Quit (* for next, # for previous menu)

    Tech_201000000115.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. = AAV 2-way module enable

(4 turns off siren during 2-way)

  1. = Unlimited

  1. to #15 = Rings to Answer

#15 = Answer Machine Over-ride