Ademco Vista-12C Program Sheet

Enter Program 1. 4111 + 8 + 0 + 0 (Display should show 00)

or

2. Power down then back up and press * and # within 1 minute

Move to Location * + Location

View Location # + Location (Display will read off one digit at a time)

Exit Program 1. *98 exits and does not allow re-entry to programming without cycling power and pressing * and #

or

2. *99 exits and does allow re-entry by Installer Code + 8 + 00

Programming can be re-entered up to 1 minute after exiting with * and # (# + 0 disables this feature)

Default Panel *97

Compatibility

Power Ratings 500ma Aux output

2A Siren output

Keypad Address (6128/6139/6150/6160 keypads)

  1. Remove power from keypad then power back up

  2. Hold 1 & 3 for 3 seconds, "ADDR = XX" or "XX" should appear (XX = current address)

  3. Within 10 seconds enter 00 to erase old address then enter new address (31)

  4. Press * to save and exit

(6150RF keypads)

  1. Power keypad down then back up

  2. Hold 1 & 3 for 3 seconds until flashing " - - 0 0" (if "DA" shows power down then up again)

  3. Press 1 and "cA XX" should appear (XX = current address)

  4. Press 31 then * to exit back to flashing " -- 0 0"

4. Press * to exit

Sniffer Test (Tests wireless sensors)

  1. Installer Code + # + 3

  2. Keypad displays all wireless sensors, faulting sensor removes it from list

  3. Exit with Installer Code + 1 (OFF)

Go-No Go Test (Verifies adequate RF by reducing receiver signal strength by 50%)

  1. Installer Code + # + 4

  2. a. Siren sounds

b. Panel may send walk test signal (If test signal was programmed)

c. "dd" appears on screen

d. Keypad will beep every 15 seconds

  1. Fault sensor, keypad should beep 3 times and display zone number,

if no beeps sound reorient or move sensor a few inches and try again

  1. Exit with Installer Code + 1 (OFF)

Hex Program Hex A = # + 10 B = # + 11 C = # + 12 D = # + 13 E = # + 14 F = # + 15

  1. = Enable

  1. = 5800 wireless with 5881 receiver

4 = 5800 wireless with RF Jam detection

  1. = Enable

(5804BD, 5827BD Keypad/Keyfobs) 01-31

  1. = 4219 Zone Expander

  2. = 4229 Zone/Relay Expander

  3. = 4204 Relay Module

(Allows access to Voice module) 1st digit = 1 to 9

2nd digit = # + 11 = * or # + 12 = #

  1. = Enable

  1. = Enable

  1. = No Fire Timeout

  1. = 4 minutes

  2. = 8 minutes

  3. = 12 minutes

  4. = 16 minutes

  1. = Enable

End Phone with * # + 11 = * # + 12 = # # + 13 = 2.5 second pause

(Hex B = #+11 C = #+12 D = #+13 E = #+14 F = #+15)

  1. = DTMF Dial

  2. = Pulse Dial, CS on Watts Line

  3. = DTMF Dial, CS on Watts Line

  1. = 3/1, 4/1 Radionics Standard

  2. = 4/2 Ademco L/S Standard

  3. = 4/2 Radionics Standard

6 = 4/2 Ademco Express

7 = Contact ID

8 = 3/1, 4/1 Ademco L/S Expanded

9 = 3/1, 4/1 Radionics Expanded

To Primary Phone To Secondary Phone

0 = All Reports Backup only

  1. = Alarms, Restore, Cancel All Other Reports

  2. = All Reports except Open/Close, Test Open/Close, Test

  3. = Alarms, Restore, Cancel All Reports

  4. = All Reports except Open/Close, Test All Reports

  5. = All Reports (Dual Reporting) All Reports

  6. = All reports except Open/Close Alarms, Open/Close, Troubles

  7. = All reports Alarms, Troubles

  8. = All reports Alarms, Open/Close, Troubles

  9. = All reports except Open/Close Alarms, Open/Close for Users 5-25, Troubles

  1. = Enable

  1. = 24 Hours

  2. = Weekly

  3. = Monthly

  1. = Sescoa

  1. = Enable

  2. = Enable for RF Arming (keyfobs etc)

  1. = 10 ms

1. Depending on version of system one of these may appear

Press 0 to bypass

Tech_201000000171.gif

2. Enter Zone to program (01 to 96) (* for next, # for previous menu)

Tech_201000000090.gif Hardwire Zone 01 to 06

4219/4229 Zone Expander Zone 10 to 17

Smoke Detectors Zone 05 only

Police Panic Zone 07

Duress Zone 08

Receiver Tamper/Trouble Zone 09

Wireless Zone 10 to 39

Fire Panic Zone 95

Medical Panic Zone 96

3. This shows current summary of Zone programming (* for next, # for previous menu)

Tech_201000000091.gif

4. Enter Zone Type (* for next, # for previous menu)

Tech_201000000092.gif 00 = Zone Disabled 08 = 24 hour Aux/Medical

  1. = Delay Zone 1 09 = Fire

  2. = Delay Zone 2 10 = Interior Delay

  3. = Perimeter/Instant 20 = Arm-Stay (RF only)

  4. = Interior Follower/Motions 21 = Arm-Away (RF only)

  5. = Trouble by Day/Alarm by Night 22 = Disarm (RF only)

  6. = 24 hour Silent/Holdup 23 = No Alarm Response

  7. = 24 hour Police Panic

5. Enter Report Code (* for next, # for previous menu)

Tech_201000000094.gif (10 in first section gives a report of A0)

Hardwire Zones will advance to step 9, for Wireless Zones continue

6. Enter type of Sensor

Tech_201000000095.gif

2 = Aux Wire (4219/4229 Zone Expander)

3 = Supervised RF (most sensors are RF)

4 = Un-Supervised RF

5 = RF Button Type (Keyfobs/Panics etc)

7. Enter Loop number (Some older systems) (* for next, # for previous menu)

Tech_201000000096.gif

Door Switch Internal switch Loop 2, external hardwire sensor Loop 1

Glassbreak Loop 1

Smoke Detectors Loop 1

Motions Loop 1

Keyfobs Bottom Right Button = Loop 1

(Each button counts as 1 zone) Top Right Button = Loop 2

Top Left Button = Loop 3

Bottom Left Button = Loop 4

8. Serial Number Programming

Tech_201000000172.gif

Press 1 and either enter serial number or trip sensor twice, 1st to learn, 2nd to confirm

Note: Serial numbers found on sticker on of sensor, if not, learn by tripping sensor

Tech_201000000173.gif This shows ready to learn

Tech_201000000174.gif This shows Serial Number either manually entered or learned

Tech_201000000175.gif This shows sensor was confirmed by activating twice

9. This is the new programming of sensor (* for next, # for previous menu)

Tech_201000000099.gif

10. Normally press 0 to return to start or 1 if if customer has 6139 keypad

Tech_201000000100.gif

  1. nd digit = Exit Alarm

I _ 0 _I Stay

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. Enter Device to program (01 to 04) (* for next, 00 to exit)

    Tech_201000000160.gif

  2. This shows summary of current Relay START programming (* for next, # for previous menu)

    Tech_201000000161.gif
(What starts the Relay)

  1. This shows summary of current Relay STOP programming (* for next, # for previous menu)

    Tech_201000000162.gif
(What stops the Relay)

  1. Enter what Relay will do when activated (* for next, # for previous menu)

    Tech_201000000163.gif
0 = No Response (or skip)

  1. = Close for 2 seconds

  2. = Close and stay closed

  3. = Continuous Pulse On/Off

5. Enter what will start the Relay (optional) (* for next, # for previous menu)

Tech_201000000164.gif 0 = Not Used (or skip)

  1. = on an Alarm

  2. = on a Zone Fault (or Keyfob button)

  3. = on a Trouble

6. Enter Zone List from *81 which STARTS Relay (optional) (* for next, # for previous menu)

Tech_201000000165.gif 0 = Not Used/Skip

  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

7. Enter Zone Type that will START the Relay (optional) (* for next, # for previous menu)

Tech_201000000166.gif 00 = Not Used (or skip) 22 = Disarming

  1. = Entry/Exit 1 31 = End of Exit Time

  2. = Entry/Exit 2 32 = Start of Entry Time

  3. = Perimeter/Instant Zone 33 = Any Burglar Alarm

  4. = Interior Follower/Motions 34 = Code + # + 7 Key Entry

  5. = Trouble by Day/Alarm by Night 35 = Code + # + 8 Key Entry

  6. = 24 hour Silent/Holdup 36 = Bell Timeout or Disarm

  7. = 24 hour Police Panic 38 = Chime

08 = 24 hour Aux/Medical 39 = Any Fire Alarm

09 = Fire 40 = Bypassing

10 = Interior Delay 41 = AC Power Failure

20 = Arm-Stay 42 = System Low Battery

21 = Arm-Away 58 = Duress

  1. Enter Zone List that will STOP the Relay (optional) (* for next, # for previous menu)

    Tech_201000000167.gif
0 = Not Used/Skip

  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

9. Enter Zone Type that will STOP the Relay (optional) (* for next, # for previous menu)

Tech_201000000110.gif

10. This shows summary of new Relay START programming (* for next, # for previous menu)

Tech_201000000168.gif

11. This shows summary of new Relay STOP programming (* for next, # for previous menu)

Tech_201000000169.gif

12. Enter next Relay to program or 00 to exit

Tech_201000000160.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. Enter Zone List to program (01 to 07) or 00 to Quit (* for next, # for previous menu)

    Tech_201000000115.gif

  2. Enter Zone Number to add to List (01, 02 etc) or 00 to Quit (* for next, # for previous menu)

    Tech_201000000116.gif
Multiple Zones can be added (example: 01* 03* 25*etc)

  1. If deleting a Zone List enter (01 to 03) or 0 to skip (* for next, # for previous menu)

    Tech_201000000117.gif

  2. If deleting Zone within Zone List enter 1 or 0 to skip (* for next, # for previous menu)

    Tech_201000000118.gif

4a. If 1 was entered from previous step enter here then 00 (* for next, # for previous menu)

Tech_201000000119.gif Multiple Zones can be deleted (example: 01* 03* 25*etc)

  1. Enter next Zone List to program or 00 to Quit (* for next, # for previous menu)

    Tech_201000000115.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. = Enable * & # or D key

(Sends "E616 Request for Service")

  1. = Local Program Lockout

  2. = Sounder Delay

  3. = Local Program Lockout/Sounder Delay

  4. = AAV 2-way Module

  5. = Local Program Lockout/AAV 2-Way Module

  6. = Sounder Delay/AAV 2-Way Module

  7. = Local Program Lockout/Sounder Delay/AAV 2-Way

  8. = Enable Exit Delay Restart

  1. = Unlimited per Armed period

  1. to 14 = Rings before answer

15 = Answering Machine over-ride