Ademco Vista-15/First Alert FA-148C Program Sheet

Enter Program 1. 4112 + 8 + 0 + 0 (Display should show 00)

or

2. Power down then back up and press * and # within 1 minute

Move to Location * + Location

View Location # + Location (Display will read off one digit at a time)

Exit Program 1. *98 exits and does not allow re-entry to programming without cycling power and pressing * and #

or

2. *99 exits and does allow re-entry by Installer Code + 8 + 00

Programming can be re-entered up to 1 minute after exiting with * and # (# + 0 disables this feature)

Default Panel *97

Compatibility

Power Ratings 600ma Aux output

2A Siren output

Keypad Address (6128/6139/6150/6160 keypads)

  1. Remove power from keypad then power back up

  2. Hold 1 & 3 for 3 seconds, "ADDR = XX" or "XX" should appear (XX = current address)

  3. Within 10 seconds enter 00 to erase old address then enter new address (31)

  4. Press * to save and exit

(6150RF keypads)

  1. Power keypad down then back up

  2. Hold 1 & 3 for 3 seconds until flashing " - - 0 0 " (if "DA" shows power down then up again)

  3. Press 1 and "cA XX" should appear (XX = current address)

  4. Press 31 then * to exit back to flashing " -- 0 0 "

4. Press * to exit

Sniffer Test (Tests wireless sensors)

  1. Installer Code + # + 3

  2. Keypad displays all wireless sensors, faulting sensor removes it from list

  3. Exit with Installer Code + 1 (OFF)

Go-No Go Test (Verifies adequate RF by reducing receiver signal strength by 50%)

  1. Installer Code + # + 4

  2. a. Siren sounds

b. Panel may send walk test signal (If test signal was programmed)

c. "dd" appears on screen

d. Keypad will beep every 15 seconds

  1. Fault sensor, keypad should beep 3 times and display zone number,

if no beeps sound reorient or move sensor a few inches and try again

  1. Exit with Installer Code + 1 (OFF)

Hex Program Hex A = # + 10 B = # + 11 C = # + 12 D = # + 13 E = # + 14 F = # + 15

  1. = Enable

  1. = 5800 Receiver

4 = 5800 with RF Jam Detection

  1. = Enable

  1. to 31

  1. = 4219 8-Zone Expander

  2. = 4229 Zone Expander Module

  3. = 4204 Relay Module

  1. = Enable (Program Zones in Zone List 3)

  1. = G 7 = H 8 = I 9 = J #10 = K #11 = L

#12 = M #13 = N #14 = O #15 = P

  1. st digit = 1 to 9

  2. nd digit = # + 11 = * or # + 12 = #

  1. = Enable

  1. = Enable

  1. = Enable

  1. = No Timeout

  1. = 4 minutes

  2. = 8 minutes

  3. = 12 minutes

  4. = 16 minutes

  1. = 45 seconds

  1. = 90 seconds

  1. = 180 seconds

  2. = 240 seconds

  1. = Enable

  1. = Enable

  2. = Enable RF Only

  1. = Enable

End Phone with * # + 11 = * # + 12 = # # + 13 = 2.5 second pause

(Hex B = #+11 C = #+12 D = #+13 E = #+14 F = #+15)

  1. = DTMF Dial

  2. = Pulse Dial, CS on Watts Line

  3. = DTMF Dial, CS on Watts Line

I _ 7 _I Secondary 1 = 3/1, 4/1 Radionics Standard

2 = 4/2 Ademco L/S Standard

3 = 4/2 Radionics Standard

6 = 4/2 Ademco Express

7 = Contact ID

8 = 3/1, 4/1 Ademco L/S Expanded

9 = 3/1, 4/1 Radionics Expanded

To Primary Phone To Secondary Phone

0 = All Reports Backup Only

  1. = Alarms, Restore, Cancel All Other Reports

  2. = All Reports except Open/Close, Test Open/Close, Test

  3. = Alarms, Restore, Cancel All Reports

  4. = All Reports except Open/Close, Test All Reports

  5. = All Reports (Dual Reporting) All Reports

  6. = All reports except Open/Close Alarms, Open/Close, Troubles

  7. = All reports Alarms, Troubles

  8. = All reports Alarms, Open/Close, Troubles

  9. = All reports except Open/Close Alarms, Open/Close for Users 5-25, Troubles

  1. = 15 seconds

  2. = 30 seconds

  3. = 45 seconds

  4. = 60 seconds

  5. = 120 seconds

  1. = 24 Hours

  2. = Weekly

  3. = Monthly

  1. = 6 Hours

  2. = 12 Hours

  3. = 18 Hours

  1. = Sescoa

0 = All Others

  1. = Enable

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

1. Press 1 here to allow confirming sensor after serial number input

Tech_201000000170.gif

2. Enter Zone to program (01 to 99) (* for next, # for previous menu)

Tech_201000000090.gif This example shows Zone 10

Hardwire Sensors Zones 01 to 06

2-wire Smokes Zone 01 only

  1. wire Smokes Zones 02 to 06

4219/4229 Zone Expander Zones 10 to 17

Receiver Tamper/Trouble Zone 09

Wireless Zones 10 to 35 (Depends on receiver capacity)

Duress Zone 92

Fire Panic Zone 95

Medical Panic Zone 96

Police Panic Zone 99

3. This shows summary of current Zone programming (* for next, # for previous menu)

Tech_201000000091.gif

4. Enter Zone Type (* for next, # for previous menu)

Tech_201000000092.gif 00 = Zone Disabled/Deleted 09 = 24 Hr Supervised Fire

  1. = Delay Zone 10 = Interior with Delay

  2. = Secondary Delay Zone 12 = Monitor Zone (non burg)

  3. = Perimeter/Instant 20 = Arm-Stay (RF only)

  4. = Interior Follower/Motions 21 = Arm-Away (RF only)

  5. = Trouble by Day/Alarm by Night 22 = Disarm (RF only)

To delete Zone enter 00 06 = 24 Hr Silent/Holdup 23 = No Alarm Response

then * until "Delete Sensor" 07 = 24 Hr Police Panic 24 = Silent Burglary

08 = 24 Hr Aux/Medical

5. Enter Report Code (* for next, # for previous menu)

Tech_201000000094.gif (10 in first section gives report of A0)

5a. Enter Response if Hardwired Zone (* for next, # for previous menu)

Tech_201000000189.gif 0 = 10msec

(Hardwire Zones only) 1 = 350msec (Default)

2 = 700msec

3 = 1.2 seconds

Hardwire Zones advance to step 9, Wireless Zones continue with step 6

6. Enter type of Sensor (* for next, # for previous menu)

Tech_201000000190.gif 2 = Auxiliary Wired (Expander)

3 = Supervised RF (Doors, Motions, Smokes)

4 = Un-Supervised RF (some Panics)

5 = RF Button Type RF (Keyfobs/Panics)

7. Serial Number Programming (* for next, # for previous menu)

Press 1 then enter serial number or trip sensor twice, Loop number will also be learned

Tech_201000000173.gif This shows ready to learn

Tech_201000000174.gif Serial and Loop number is manually entered here

or learned by tripping twice (keypad will beep)

(Serial number sticker is on sensor)

8. If "Set to Confirm" was selected while first entering *56 this will appear

Tech_201000000191.gif Trip sensor again to confirm

If incorrect serial number was learned this will appear

Tech_201000000192.gif

(This can be used to find out a serial number if sticker was removed)

9. This shows summary of new sensor programming (* for next, # for previous menu)

Tech_201000000099.gif

10. Press 0 for next sensor or 1 to enter Alpha descriptions

Tech_201000000100.gif

11. Enter next sensor or 00 to exit *56 menu

Tech_201000000090.gif

12. Press * or # to exit

Tech_201000000193.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

1. Press 1 here to allow confirming sensor after serial number input

Tech_201000000170.gif

2. Enter Zone to program (01 to 99) then *

Tech_201000000176.gif

3. Enter Zone Type (Display moves to Report Code, # starts over)

Tech_201000000177.gif 00 = Zone Disabled/Deleted 09 = 24 Hr Supervised Fire

  1. = Delay Zone 10 = Interior with Delay

  2. = Secondary Delay Zone 12 = Monitor Zone (non burg)

  3. = Perimeter/Instant 20 = Arm-Stay (RF only)

  4. = Interior Follower/Motions 21 = Arm-Away (RF only)

  5. = Trouble by Day/Alarm by Night 22 = Disarm (RF only)

To delete Zone enter 00 06 = 24 Hr Silent/Holdup 23 = No Alarm Response

then * until "Delete Sensor" 07 = 24 Hr Police Panic 24 = Silent Burglary

08 = 24 Hr Aux/Medical

4. Display moves to Report Code, if needed enter 10 (Display moves to Sensor Type, # starts over)

Tech_201000000178.gif

A key moves left through fields if needed

B key moves right through fields if needed

C key copies previous Zone attributes

Hardwired Zones automatically skip to step 9, Wireless Zones continue with step 5

5. Enter Wireless sensor type then *

Tech_201000000179.gif 3 = Supervised RF (Doors, Motions, Smokes)

4 = Un-Supervised RF (some Panics)

5 = RF Button Type RF (Keyfobs/Panics)

6. If Wireless enter Serial Number or trip sensor twice (Keypad will beep twice as Sensor learns)

Tech_201000000180.gif

Tech_201000000181.gif

7. Enter Loop only if manually entering Serial Number (* for next, # for previous menu)

Tech_201000000182.gif

8. If "Set to Confirm" was selected while first entering *58 this will appear

Tech_201000000183.gif Trip sensor again to confirm

Tech_201000000184.gif This shows panel and sensor serials match

9. Enter next sensor or 00 then * or # to exit *58 menu

Tech_201000000185.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. = January 08 = August

  2. = February 09 = September

  3. = March #10 = October

  4. = April #11 = November

  5. = May #12 = December

  6. = June

I _ 5 _I End 2 = 2nd Weekend

3 = 3rd Weekend

4 = 4th Weekend

5 = Last Weekend

6 = Next to Last Weekend

  1. = 3rd from Last Weekend

I _ 0 _I DS Priority 0 = Primary Phone First

  1. = LRR first

  1. Enter Device to program (01 to 04) (* for next, 00 to exit)

    Tech_201000000160.gif
  1. to 02 for 4229 Relay Module/Zone Expander

  1. to 04 for 4204 Relay Module

  1. to 04 for X-10 Powerline Carrier

  2. This shows summary of current Relay START programming (* for next, # for previous menu)

    Tech_201000000161.gif
(What starts the Relay)

  1. This shows summary of current Relay STOP programming (* for next, # for previous menu)

    Tech_201000000162.gif
(What stops the Relay)

  1. Enter what Relay will do when activated (* for next, # for previous menu)

    Tech_201000000163.gif
0 = No Response (or skip)

  1. = Close for 2 seconds

  2. = Close and stay closed

  3. = Continuous Pulse On/Off

5. Enter what will start the Relay (optional) (* for next, # for previous menu)

Tech_201000000164.gif 0 = Not Used (or skip)

  1. = on an Alarm

  2. = on a Zone Fault (or Keyfob button)

  3. = on a Trouble

6. Enter Zone List from *81 which STARTS Relay (optional) (* for next, # for previous menu)

Tech_201000000165.gif 0 = Not Used (or skip)

  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

7. Enter Zone Type that STARTS Device (* for next, # for previous menu)

Tech_201000000166.gif 00 = Skip this step 22 = Disarming

  1. = Delay Zone 24 = Silent Burglary

  2. = Secondary Delay Zone 31 = End of Exit Time

  3. = Perimeter/Instant 32 = Start of Entry Time

  4. = Interior Follower/Motions 33 = Any Burglar Alarm

  5. = Trouble by Day/Alarm by Night 36 = At Bell Timeout or Disarm

  6. = 24 hour Silent/Holdup 38 = Chime

  7. = 24 hour Police Panic 39 = Any Fire Alarm

08 = 24 hour Aux/Medical 40 = Bypassing

09 = Fire 41 = AC Power Failure

10 = Interior Delay 42 = System Low Battery

20 = Arm-Stay 43 = Communication Failure

21 = Arm-Away 52 = Kissoff

58 = Duress

  1. Enter Zone List that will STOP the Relay (optional) (* for next, # for previous menu)

    Tech_201000000167.gif
0 = Not Used/Skip

  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

9. Enter Zone Type that will STOP the Relay (optional) (* for next, # for previous menu)

Tech_201000000110.gif

10. This shows summary of new Relay START programming (* for next, # for previous menu)

Tech_201000000168.gif

11. This shows summary of new Relay STOP programming (* for next, # for previous menu)

Tech_201000000169.gif

12. If this is an X-10 Device enter 1, if not enter 0 (* for next, # for previous menu)

Tech_201000000114.gif

13. Enter next Relay to program or 00 to exit

Tech_201000000160.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. Enter Zone List to program or 00 to Quit (* for next, # for previous menu)

    Tech_201000000115.gif
  1. to 03 for standard X-10 or Relay Devices

03 is also used for *26 Chime by Zone

  1. is used for Cross Zoning

  2. is used for Night-Stay

2. Enter Zone Number to add to List (01, 02 etc) or 00 to Quit (* for next, # for previous menu)

Tech_201000000116.gif Multiple Zones can be added (example: 01* 03* 25*etc)

3. If deleting a Zone List enter (01 to 03) or 0 to skip (* for next, # for previous menu)

Tech_201000000117.gif

4. If deleting Zone within Zone List enter 1 or 0 to skip (* for next, # for previous menu)

Tech_201000000118.gif

4a. If 1 was entered from previous step enter here then 00 (* for next, # for previous menu)

Tech_201000000119.gif Multiple Zones can be deleted (example: 01* 03* 25*etc)

5. Enter next Zone List to program or 00 to Quit (* for next, # for previous menu)

Tech_201000000115.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. = Enable

  1. = 45 seconds

  2. = 60 seconds

  3. = 90 seconds

  4. = 120 seconds

  5. = 180 seconds

  6. = 240 seconds

  1. = 1 minutes

  2. = 2 minutes

  3. = 3 minutes

  1. = Alarm/Restore

  2. = Trouble/Restore

4 = Bypass/Bypass Restore

8 = Open/Close

F (#15) All Options Enabled

  1. = AAV 2-way module enabled

8 = Enable Exit Delay Restart

12 = Exit Delay Restart & AAV Enable

  1. = Keypad Display

  2. = Keypad Display/Sounder

  3. = Keypad Display/Sounder/Device #2 starts

  1. to 15 = 1 to 15 Alarms while Armed

  1. to 14 = Rings before answer

15 = Answering Machine over-ride