Ademco Vista-20/First Alert FA-160C Program Sheet

Enter Program 1. 4112 + 8 + 0 + 0 (Display should show 00)

or

2. Power down then back up and press * and # within 1 minute

Move to Location * + Location

View Location # + Location (Display will read off one digit at a time)

Exit Program 1. *98 exits and does not allow re-entry to programming without cycling power and pressing * and #

or

2. *99 exits and does allow re-entry by Installer Code + 8 + 00

Programming can be re-entered up to 1 minute after exiting with * and # (# + 0 disables this feature)

Default Panel *97

Compatibility

Power Ratings 600ma Aux output

2A Siren output

Keypad Address (6128/6139/6150/6160 keypads)

  1. Remove power from keypad then power back up

  2. Hold 1 & 3 for 3 seconds, "ADDR = XX" or "XX" should appear (XX = current address)

  3. Within 10 seconds enter 00 to erase old address then enter new address (31)

  4. Press * to save and exit

(6150RF keypads)

  1. Power keypad down then back up

  2. Hold 1 & 3 for 3 seconds until flashing " - - 0 0" (if "DA" shows power down then up again)

  3. Press 1 and "cA XX" should appear (XX = current address)

  4. Press 31 then * to exit back to flashing " -- 0 0"

4. Press * to exit

Sniffer Test (Tests wireless sensors)

  1. Installer Code + # + 3

  2. Keypad displays all wireless sensors, faulting sensor removes it from list

  3. Exit with Installer Code + 1 (OFF)

Go-No Go Test (Verifies adequate RF by reducing receiver signal strength by 50%)

  1. Installer Code + # + 4

  2. a. Siren sounds

b. Panel may send walk test signal (If test signal was programmed)

c. "dd" appears on screen

d. Keypad will beep every 15 seconds

  1. Fault sensor, keypad should beep 3 times and display zone number,

if no beeps sound reorient or move sensor a few inches and try again

  1. Exit with Installer Code + 1 (OFF)

Hex Program Hex A = # + 10 B = # + 11 C = # + 12 D = # + 13 E = # + 14 F = # + 15

I _ 0 _I Partition 2 1 = Enable

  1. = 5800 Receiver

I _ 0 _I Partition 2 1 = Enable

(Partition 2 RF House ID = Partition 1 House ID + 1) 01 to 31

  1. = 4219 8-Zone Expander

  2. = 4229 Zone Expander Module

  3. = 4204 Relay Module

  1. = G 7 = H 8 = I 9 = J #10 = K #11 = L

#12 = M #13 = N #14 = O #15 = P

(Allows access to Voice module) 1st digit = 1 to 9

2nd digit = # + 11 for * or # + 12 for #

  1. = Enable

  1. = Enable

  1. = Enable

  1. = No Timeout

  1. = 4 minutes

  2. = 8 minutes

  3. = 12 minutes

  4. = 16 minutes

I _ 2 _I Partition 2 1 = 20 seconds

2 = 30 seconds

3 = 45 seconds

(Exit Delay = Entry Delay + 40 Seconds) 4 = 60 seconds

  1. = 90 seconds

I _ 1 _I Partition 2 1 = Enable

I _ 0 _I Partition 2 1 = Enable

  1. = Enable

End Phone with * # + 11 = *# + 12 = # # + 13 = 2.5 second pause

(Hex B = #+11 C = #+12 D = #+13 E = #+14 F = #+15)

  1. = DTMF Dial

  2. = Pulse Dial, CS on Watts Line

  3. = DTMF Dial, CS on Watts Line

I _ 7 _I Partition 2 1 = 3/1, 4/1 Radionics Standard

2 = 4/2 Ademco L/S Standard

3 = 4/2 Radionics Standard

6 = 4/2 Ademco Express

7 = Contact ID

8 = 3/1, 4/1 Ademco L/S Expanded

9 = 3/1, 4/1 Radionics Expanded

To Primary Phone To Secondary Phone

0 = All Reports Backup Only

  1. = Alarms, Restore, Cancel All Other Reports

  2. = All Reports except Open/Close, Test Open/Close, Test

  3. = Alarms, Restore, Cancel All Reports

  4. = All Reports except Open/Close, Test All Reports

  5. = All Reports (Dual Reporting) All Reports

  1. = Enable

  1. = 24 Hours

  2. = Weekly

  3. = Monthly

  1. = 6 Hours

  2. = 12 Hours

  3. = 18 Hours

  1. = Enable

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

1. This may appear

Tech_201000000170.gif

(Select 0 for No)

2. Enter Zone to program (01 to 99) (* for next, # for previous menu)

Tech_201000000090.gif

Hardwire Zone 01 to 08

4219/4229 Zone Expander Zone 10 to 17

Receiver Tamper/Trouble Zone 09

Wireless Zone 10 to 39 (Depends on receiver capacity)

Duress Zone 92

Fire Panic Zone 95

Medical Panic Zone 96

Police Panic Zone 99

3. This shows current summary of Zone programming (* for next, # for previous menu)

Tech_201000000091.gif

4. Enter Zone Type (* for next, # for previous menu)

Tech_201000000092.gif 00 = Zone Disabled 08 = 24 hour Aux/Medical

  1. = Delay Zone 09 = Fire

  2. = Delay 2 Zone 10 = Interior Delay

  3. = Perimeter/Instant 20 = Arm-Stay (RF only)

  4. = Interior Follower/Motions 21 = Arm-Away (RF only)

  5. = Trouble by Day/Alarm by Night 22 = Disarm (RF only)

  6. = 24 hour Silent/Holdup 23 = No Alarm Response

  7. = 24 hour Police Panic 24 = Silent Burglary

5. Enter Response Time (Hardwire Zones only) (* for next, # for previous menu)

Tech_201000000189.gif 0 = 10msec

1 = 350msec

2 = 700msec

6. Program Partition of Zone (* for next, # for previous menu)

Tech_201000000093.gif 1 = Partition 1

2 = Partition 2

(Common Zone programming in *81 using Zone List 04)

The common zone will sound and report alarms only if both partitions are armed . When only one partition

is armed, the common zone is automatically treated as if it were a zone type 23 (no alarm response) zone.

A fault on the common zone is displayed in both partitions.

Either partition may arm its system if the common zone is faulted, but once armed, the other partition cannot arm.

That partition must first bypass the common zone or correct the fault before arming.

Either partition can clear and restore the common zone after an alarm.

7. Enter Report Code (* for next, # for previous menu)

Tech_201000000094.gif (10 in first section gives a report of A0)

Hardwire Zones will advance to step 11, for Wireless Zones continue with step 9

(If it doesn't go to next steps check if Receiver has been programmed in *22)

8. Enter type of Sensor

Tech_201000000095.gif 2 = Auxiliary Wired Sensor (if 4219/4229 Zone Expander)

3 = Supervised RF (most sensors are RF)

4 = Un-Supervised RF

5 = RF Button Type (Keyfobs/Panics etc)

(New versions may skip step 8 and move to step 9, learn Loop number after learning sensor)

9. Enter Loop number (Some older systems) (* for next, # for previous menu)

Tech_201000000096.gif

Door Switch Internal switch Loop 2

External hardwire sensor Loop 1

Glassbreak Loop 1

Smoke Detectors Loop 1

Motions Loop 1

Keyfobs Bottom Right Button = Loop 1

(Each button counts as 1 zone) Top Right Button = Loop 2

Top Left Button = Loop 3

Bottom Left Button = Loop 4

10. Learning Sensor

Tech_201000000097.gif

Press 1 and trip sensor twice (Serial number cannot be entered)

Tech_201000000098.gif

11. This is the new programming of sensor (* for next, # for previous menu)

Tech_201000000099.gif

12. 0 or * returns to beginning, 1 programs alpha descriptors

Tech_201000000100.gif

To delete a Zone set Zone Type as 00 then * until "Delete Sensor?", press 1 to delete

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

I _ 0 _I Partition 2

I _ 0 _I _ 0 _I Partition 2 (1st digit Stay, 2nd Away)

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. Enter Device to program (01 to 08) (* for next, 00 to exit)

    Tech_201000000101.gif
  1. to 04 are for Output Relays and X-10

05 to 08 X-10 only

2. This shows summary of current Device START programming (* for next, # for previous menu)

Tech_201000000102.gif (What starts the Device)

3. This shows summary of current Device STOP programming (* for next, # for previous menu)

Tech_201000000103.gif (What stops the Device)

4. Enter what Device will do when activated (* for next, # for previous menu)

Tech_201000000104.gif 0 = No Response (or skip)

  1. = Close for 2 seconds

  2. = Close and stay closed

  3. = Continuous Pulse On/Off

5. Enter what will start the Device (optional) (* for next, # for previous menu)

Tech_201000000105.gif 0 = Not Used (or skip)

  1. = on an Alarm

  2. = on a Zone Fault (or Keyfob button)

  3. = on a Trouble

6. Enter Zone List from *81 which STARTS Device (optional) (* for next, # for previous menu)

Tech_201000000106.gif 0 = Not Used (or skip)

  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

7. Enter Zone Type that will START the Device (optional) (* for next, # for previous menu)

Tech_201000000107.gif 00 = Not Used (or skip) 24 = Silent Burglary

  1. = Entry/Exit Zone 31 = End of Exit Time

03 = Perimeter/Instant Zone 32 = Start of Entry Time

04 = Interior Follower/Motions 33 = Any Burglar Alarm

05 = Trouble by Day/Alarm by Night 36 = Bell Timeout or Disarm

06 = 24 hour Silent/Holdup 38 = Chime

07 = 24 hour Police Panic 39 = Any Fire Alarm

08 = 24 hour Aux/Medical 40 = Bypassing

09 = Fire 41 = AC Power Failure

10 = Interior Delay 42 = System Low Battery

20 = Arm-Stay 43 = Communication Failure

21 = Arm-Away 52 = Kissoff

22 = Disarming 58 = Duress

8. Enter which Partition will START this Device (Optional) (* for next, # for previous menu)

Tech_201000000108.gif 0 = Any Partition

  1. = Partition 1

  2. = Partition 2

9. Enter Zone List that will STOP the Device (optional) (* for next, # for previous menu)

Tech_201000000109.gif 0 = Not Used (or skip)

  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

10. Enter Zone Type that will STOP the Device (optional) (* for next, # for previous menu)

Tech_201000000110.gif

11. Enter which Partition will STOP this Device (optional) (* for next, # for previous menu)

Tech_201000000111.gif 0 = Any Partition

  1. = Partition 1

  2. = Partition 2

12. This shows summary of new Device START programming (* for next, # for previous menu)

Tech_201000000112.gif

13. This shows summary of new Device STOP programming (* for next, # for previous menu)

Tech_201000000113.gif

14. If this is an X-10 Device enter 1, if not enter 0 (* for next, # for previous menu)

Tech_201000000114.gif

15. Enter next Device to program or 00 to exit

Tech_201000000101.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. Enter Zone List to program (01 to 04) or 00 to Quit (* for next, # for previous menu)

    Tech_201000000115.gif
  1. = Zone List 1

  2. = Zone List 2

  3. = Zone List 3

2. Enter Zone Number to add to List (01, 02 etc) or 00 to Quit (* for next, # for previous menu)

Tech_201000000116.gif Multiple Zones can be added (example: 01* 03* 25*etc)

3. If deleting a Zone List enter (01 to 04) or 0 to skip (* for next, # for previous menu)

Tech_201000000117.gif

  1. If deleting Zone within Zone List enter 1 or 0 to skip (* for next, # for previous menu)

    Tech_201000000118.gif

4a. If 1 was entered from previous step enter here then 00 (* for next, # for previous menu)

Tech_201000000119.gif Multiple Zones can be deleted (example: 01* 03* 25*etc)

  1. Enter next Zone List to program or 00 to Quit (* for next, # for previous menu)

    Tech_201000000115.gif

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  1. = Alarm/Restore

  2. = Trouble/Restore

4 = Bypass/Bypass Restore

8 = Open/Close

F (#15) All Options Enabled

  1. = AAV

  1. = KP Display

  2. = KP Display/Sounder

  3. = KP Display/Sounder/Device 2 starts

  1. = Unlimited per Armed period

  1. to 14 = Rings before answer

15 = Answering Machine over-ride